Skip to content

How many bundles of shingles does the roof need?

Squares in, or a footprint and a pitch. Bundles out, with the waste shown rather than buried, and the starter and cap beside them — on the same coverage figures the full takeoff orders from.

The roof

Start from

One square is 100 sq ft of roof SURFACE, after the pitch. If what you have is the house footprint, use the other way in and the slope factor is applied for you.

The side the ridge runs along, measured to the edge of the overhang — not the heated floor plan.

Rise in 12. Write 6, 6/12 or 6:12. The slope factor comes from this, and it is the number that turns the footprint into roof.

Roof style

Decides the edges the starter and cap run along, and the waste default: a hip cuts every course at both ends.

Waste

How cut up

Dormers, valleys and an ell all mean more offcuts. The percentages are the estimating-guide bands, and the field beside this overrides them.

Type your own figure to override the default. It is added to the field shingles; starter and cap carry their own smaller allowance.

Products

The default residential shingle. GAF Timberline HDZ and equivalents.

105 ft only if you separate every sheet at the center perforation. Run whole, a bundle covers 52.5 ft — pick the other Owens Corning line for that.

Runs every ridge and every hip.

Architectural (laminated) shingles

Bundles to order
45bundles
3 a square at 33.33 sq ft each, with 10% waste
Squares
13.42
1,342 sq ft of roof surface
Squares with waste
14.76
what the 45 bundles cover: 15 sq

6/12 is a slope factor of 1.1180: the roof has 11.8% more surface than the footprint under it. Ordering off the footprint alone is how a job runs short on the last course.

Starter and cap

Starter strip
2bundles
147.1 ft of eave and rake at 105 ft a bundle
Hip and ridge cap
2bundles
40 ft of ridge and hip at 25 ft a bundle

Starter runs the rakes as well as the eaves — GAF lists starter at eaves and rakes as a warranty condition — which is why the eave length alone would order half of it. Both lines carry 5% for cuts, not the field waste.

Bundles are a third of the order

Underlayment, drip edge, nails, cap nails, valley metal, pipe boots and step flashing come off the same roof. The full takeoff orders all of it from the same measurements.

Run the full takeoff →

The same roof on every shingle line

Bundles needed for this roof, by shingle line, at the same waste allowance
Shingle linePer squareBundles
Architectural (laminated)
33.33 sq ft a bundle, 21 pieces
345
Three-tab
33.33 sq ft a bundle, 26.67 pieces
345
Premium / designer
25 sq ft a bundle, 14 pieces
460
The formula
squares = footprint area × slope factor ÷ 100 squares with waste = squares × (1 + waste) bundles = ceil( squares with waste × bundles per square ) starter bundles = ceil( (eaves + rakes) × (1 + 5%) ÷ ft per bundle ) cap bundles = ceil( (ridges + hips) × (1 + 5%) ÷ ft per bundle )

A square is 100 sq ft of roof surface — the sloped surface, not the footprint under it. An architectural shingle is packed at 33.33 sq ft a bundle, so 3 bundles make a square; a three-tab is packed the same way with more pieces in the bundle. Premium and designer lines are heavier and go 4 bundles to the square at 25 sq ft each, and some go five, which is why the line is a picker rather than an assumption.

Waste is added to the field shingles only. The defaults are the estimating-guide bands: 10% on a simple gable, 15% on a simple hip, 15% on a cut-up gable and 18% on a cut-up hip. Starter and cap are lengths along edges, not areas, and carry 5% for cuts.

Why starter is driven by the rakes as well as the eaves

Starter at the rakes is not an upgrade. GAF’s residential warranty lists starter strip shingles at eaves and rakes as a qualifying accessory, and without it the roof does not get the wind rating the homeowner was sold. Driving starter off the eaves alone under-orders a gable by roughly half, which is why this page asks for the eave and rake length together, and derives both when you give it a footprint.

Where every figure on this page comes from
  • Architectural shingles. The Home Depot listing, GAF Timberline HDZ, 33.33 sq ft per bundle, 3 bundles per square, 21 pieces per bundle (https://www.homedepot.com/p/309755323)
  • Three-tab shingles. Trade-standard three-tab packaging: 33.33 sq ft per bundle, 3 bundles per square, 80 shingles per square. A three-tab is 36 x 12 in laid at a 5 in exposure, so each one covers 36 x 5 = 180 sq in = 1.25 sq ft, and 100 / 1.25 = 80. (The 5-5/8 in exposure quoted elsewhere on this page is the ARCHITECTURAL one, which is why it yields 71 and not 80; it was copied into this line by mistake.)
  • Premium shingles. GAF Camelot II: 25 sq ft per bundle, 4 bundles per square, 14 pieces per bundle (56 per square). Premium lines vary -- GAF Grand Sequoia is FIVE bundles per square (one of 16 plus four of 14) -- so confirm against the specific product's data sheet
  • Owens Corning starter. Owens Corning Starter Strip Plus: 16 shingles per bundle, each packaged as two pieces joined by a center perforation — 105 lineal ft per bundle once separated, 52.5 ft if the sheets are run whole (https://owenscorning.com/roofing/products/starter-strip-plus)
  • GAF Pro-Start. GAF Pro-Start: approx. 120.33 lineal ft per bundle ONLY when each of the 19 full sheets is split in half into 38 pieces of 6.5 x 38 in. Run unsplit it covers about 60 lineal ft (https://www.gaf.com/en-us/roofing-products/residential-roofing-products/starter-strip-shingles/standard/pro-start)
  • GAF WeatherBlocker. GAF WeatherBlocker: 100 lineal ft per bundle when the perforated full sheets are split, 50 lineal ft unsplit (https://www.gaf.com/en-us/products/weatherblocker)
  • GAF Seal-A-Ridge. GAF Seal-A-Ridge data sheet: 4 bundles cover approx. 100 lineal ft, i.e. 25 lineal ft per bundle (https://documents.gaf.com/data-sheets/sealaridge-ridge-cap-shingles-105-reshr112-(9-22)-_data-sheet.pdf)
  • GAF TimberTex. GAF TimberTex: 20 lineal ft per bundle, 30 pieces. This is the cap paired with Timberline HDZ for the Golden Pledge warranty (https://www.homedepot.com/p/206670781)
  • CertainTeed Shadow Ridge. CertainTeed Shadow Ridge is sold in two formats and they are not interchangeable. ENGLISH: 12 x 36 in strip separating into three 12 x 12 in pieces, 5 in exposure, 30 lineal ft per bundle (72 caps). METRIC: 13-1/4 x 39-3/8 in strip into four pieces, 5-5/8 in exposure, 45 lineal ft per bundle. Both figures from CertainTeed's published specification for the product; Lowe's lists the English bundle as 31 lineal ft on the title and 30 in the coverage field, so 30 is the figure to order against
  • Cap cut from three-tab. Cap cut from three-tab shingles, three caps per shingle: 31-35 lineal ft per bundle depending on exposure (Louisiana roofing contractor estimating study guide). 33 is used -- the MIDPOINT, not the top of the range, because a roofer running a longer exposure gets the 31 end and would be short on a long ridge
  • Waste allowance. Common estimating practice, and the sources give two bands. A Louisiana roofing contractor estimating study guide gives 5-8% simple gable / 10-12% hip / 15-20% cut-up hip-and-valley; other estimating sources give 10-12% gable / 15% hip / 15-20% with dormers and valleys. The defaults here follow the SECOND band, which is the more conservative of the two: 10% simple gable (its floor), 15% simple hip (its figure), 15% cut-up gable and 18% cut-up hip (within its 15-20%). A practice figure, not a specification -- it is an editable input on R1

These are the same strings the engine carries beside each coverage figure; a material with no source is refused outright. The disagreements between published sources are written out on the math page rather than averaged away.

A 40 × 30 gable at 6/12, on architectural shingles
Footprint
40 ft × 30 ft = 1,200 sq ft, including the overhangs
Pitch
6/12
Shingle
Architectural (laminated), 3 bundles a square
Waste
10%, the simple-gable default
  1. Slope factor. √(6² + 12²) ÷ 12 = 1.1180. The roof has 11.8% more surface than the footprint.
  2. Squares. 1,200 × 1.1180 = 1,341.6 sq ft, which is 13.42 squares.
  3. Squares with waste. 13.42 × 1.10 = 14.76 squares to order against.
  4. Bundles. 1,475.8 sq ft ÷ 33.33 sq ft a bundle = 44.28, rounded up to 45 bundles — 3 a square. The 24 sq ft left over is the rounding, not more waste.
  5. Starter. Two eaves of 40 ft and four rakes of 15 × 1.1180 ft make 147.1 ft. × 1.05 ÷ 105 ft a bundle = 1.47, so 2 bundles of Owens Corning Starter Strip Plus, split (105 ft).
  6. Cap. The ridge is 40 ft and a gable has no hips. × 1.05 ÷ 25 ft a bundle = 1.68, so 2 bundles of GAF Seal-A-Ridge (25 ft).

45 bundles of architectural shingles for 13.42 squares of roof, plus 2 of starter and 2 of cap. Ordering off the 1,200 sq ft footprint instead would have been 40 bundles — short by 5 on the last courses.

Figures from The Home Depot listing, GAF Timberline HDZ, 33.33 sq ft per bundle, 3 bundles per square, 21 pieces per bundle; Owens Corning Starter Strip Plus — 105 lineal ft per bundle once split; GAF Seal-A-Ridge data sheet — 25 lineal ft per bundle; The waste bands and the slope factor table, with every source written out; How many squares is my roof? The short guide.

Questions

How many bundles of shingles are in a square?
3 for architectural and three-tab shingles, which are both packed at 33.33 sq ft a bundle — 100 ÷ 33.33 is 3. Premium and designer lines are heavier: 4 bundles at 25 sq ft is the common figure and some lines are five, so read the wrapper or the data sheet before you multiply.
How many squares is my roof?
Measure the footprint — the area the roof covers seen from above, overhangs included — multiply by the slope factor for the pitch, and divide by 100. A 6/12 roof multiplies by 1.118, so a 1,200 sq ft footprint is about 13.4 squares of roof. This page does that arithmetic when you give it a length, a width and a pitch, and the guide on how many squares a roof is walks through it by hand.
Do I add waste before or after I work out the bundles?
Before. Waste is added to the roof area, and the bundles are rounded up from the result: a 10% allowance on 13.4 squares is 14.8 squares, and that is the figure the bundle count comes from. Adding a percentage to a bundle count that has already been rounded up adds it twice.
How much waste should I allow?
The estimating guides give two bands and this page uses the more conservative one: 10% on a simple gable, 15% on a simple hip, 15% on a cut-up gable and 18% on a cut-up hip. A hip cuts every course at both ends, which is why it wastes more than a gable of the same size. It is a practice figure, not a specification, so the field is editable.
Do the bundles include the starter strip and the ridge cap?
No. Starter and cap are separate products sold by the lineal foot of edge, not by area. Starter runs the eaves and the rakes — GAF lists both as a warranty condition — and a bundle of Owens Corning Starter Strip Plus, split covers 105 ft once the sheets are split. Cap runs every ridge and hip; GAF Seal-A-Ridge covers 25 ft a bundle, GAF TimberTex 20 ft, and cap cut from three-tab about 33 ft. Pick the one you are buying; the spread is wide enough to matter.
Should I measure the footprint or the roof itself?
Either, as long as you know which you have. A footprint is what the roof covers on the ground and needs the slope factor applied; a roof surface, in squares, has already had it. The one mistake this page cannot catch is a footprint typed into the squares field — it will give you a count that is short by the pitch, which on a 6/12 is about 12%.
Does this work with no signal?
Yes. Open it once on a connection and the arithmetic keeps running on your phone with nothing on the signal bar, in a basement or a subdivision with one bar. The calculator is public and the result is never held back; saving the roof to a job is what needs the email sign-in.
Shingle Calculator — How Many Bundles | RoofParrot