How many squares is my roof?
The unit, the one formula, a house you can follow with a pencil, and the table of slope factors you will want to screenshot.
The short answer
One roofing square is 100 square feet of roof surface. To count them, measure the footprint of the roof — length times width, including the overhangs — multiply by the slope factor for the pitch, and divide by 100.
A 40 × 30 ft house at a 6/12 pitch is 1,200 × 1.1180 ÷ 100 = 13.42 squares, not the 12 you get from the footprint alone.
What a square is, and what it is not
Roofing is priced, ordered and quoted by the square: 100 sq ft of the sloped surface a shingle actually sits on. Shingles are packed to it — an architectural shingle at 33.33 sq ft a bundle goes 3 bundles to the square — and so is labor, which is why a roofer’s first question about any job is how many squares it is.
It is not the floor area of the house, and it is not the footprint either. The footprint is the roof’s shadow on the ground; the roof is the sloped surface above it, and the sloped surface is always bigger. How much bigger is the slope factor.
The slope factor
A pitch is written as rise in 12: a 6/12 roof climbs 6 inches for every 12 it travels. The sloped surface is the hypotenuse of that triangle, so the factor is plain Pythagoras — √(rise² + 12²) ÷ 12. For 6/12 that is √(36 + 144) ÷ 12 = 1.1180, which means the roof has 11.8% more surface than the footprint under it. Steeper roofs have more; a 12/12 has 41.4% more.
If you do not know the pitch, hold a level out horizontally from the roof surface, mark 12 inches along it and measure straight down to the deck: that drop in inches is the rise. The pitch calculator turns any rise, angle or grade into the factor.
A worked example: 40 × 30 at 6/12
- Footprint. 40 ft × 30 ft = 1,200 sq ft. Measure to the edge of the overhang, not the wall — the roof covers the overhang too.
- Slope factor. 6/12 is 1.1180.
- Roof surface. 1,200 × 1.1180 = 1,341.6 sq ft.
- Squares. 1,341.6 ÷ 100 = 13.42 squares.
Skipping the slope factor gives 12 squares — 1.42 squares short, which on architectural shingles at 3 bundles a square is about 5 bundles, before waste. That is a second trip to the supplier in the middle of a tear-off.
Ordering adds a waste allowance on top of the measured squares — 10% on a simple gable, 15% on a simple hip, more on a cut-up roof — and then rounds up to whole bundles. The shingle calculator does that step, and the squares and materials calculator goes on to the underlayment, starter, cap, drip edge and nails.
Slope factors for every common pitch
Multiply the footprint by the factor in the middle column. Each is √(rise² + 144) ÷ 12, computed rather than copied, and the same function every calculator on this site uses.
| Pitch | Slope factor | More roof than footprint | Angle |
|---|---|---|---|
| 1/12 | 1.0035 | 0.3% | 4.8° |
| 2/12 | 1.0138 | 1.4% | 9.5° |
| 3/12 | 1.0308 | 3.1% | 14.0° |
| 4/12 | 1.0541 | 5.4% | 18.4° |
| 5/12 | 1.0833 | 8.3% | 22.6° |
| 6/12 | 1.1180 | 11.8% | 26.6° |
| 7/12 | 1.1577 | 15.8% | 30.3° |
| 8/12 | 1.2019 | 20.2% | 33.7° |
| 9/12 | 1.2500 | 25.0% | 36.9° |
| 10/12 | 1.3017 | 30.2% | 39.8° |
| 11/12 | 1.3566 | 35.7% | 42.5° |
| 12/12 | 1.4142 | 41.4% | 45.0° |
| 14/12 | 1.5366 | 53.7% | 49.4° |
| 16/12 | 1.6667 | 66.7% | 53.1° |
| 18/12 | 1.8028 | 80.3% | 56.3° |
Roofs that are not one rectangle
Most are not. Break the footprint into rectangles — the main house, the ell, the garage, each porch — take each one’s footprint times its own slope factor, and add the surfaces up before dividing by 100. A section at a different pitch gets a different factor, which is the detail a single multiplication misses. Dormers add surface that is hard to measure from the ground; a 15% to 18% waste allowance on a cut-up roof is partly an admission of that.
A hip roof of the same footprint and pitch has the same number of squares as a gable — the slope factor does not care which way the planes face. What changes is the edges: a hip has no rakes, more eave, and four hips in place of most of the ridge, so the starter and cap come out differently even though the bundles do not.
Or let the satellite photo do the measuring
Type the address, trace the roof outline on the photo, set the pitch, and the squares come back with the edge lengths — then priced and ready to send.
The trace is your own measurement, off the outline you drew and the pitch you set. It cannot see a dormer cheek or anything vertical, and the photo is only as current as the day it was taken. What a free roof measurement does and does not get you.
Questions
- How many squares is a 2,000 sq ft house?
- It depends on what the 2,000 is. If it is the roof footprint at 6/12, it is 2,000 × 1.1180 ÷ 100 = 22.4 squares. If it is the floor area of a two-story house, the footprint is roughly half that plus the overhangs, and the answer is nearer 11 than 22. Measure the footprint; do not infer it from the listing.
- Do I include the overhangs?
- Yes. The roof covers the overhangs, so the footprint is measured to the drip edge, not to the wall. A 12 in overhang all round a 40 × 30 house adds 144 sq ft of footprint before the slope factor, which is more than a square of shingles once it is applied.
- Is a square the same as 100 square feet of shingles?
- Of installed, exposed shingles, yes: 3 bundles at 33.33 sq ft each cover one square. The shingles themselves overlap, so the material in a square is more than 100 sq ft of asphalt; the coverage figure on the wrapper already allows for the lap.