How to bid a roofing job
Seven steps, in the order the money moves: measure, take off the materials, price the labor, add what the business costs to run, decide what to earn, write it down, and ask for the deposit. One roof — a 40 × 30 gable at 6/12 — runs through every step, and every figure on this page is computed by the same code the bid calculator runs.
About the figures in the example
The prices are the ones in the bid calculator’s worked example — a contractor’s own supplier prices and labor rate in that story. They are here to show the arithmetic. We do not publish market rates, because a shingle price or a labor rate we invented would be wrong in your market on the day you used it, and a wrong number that looks confident is worse than a blank field. The coverage figures, waste factor and slope factor behind the takeoff are published with their sources on how the math works.
1. Measure the roof: squares, pitch, edges
A roofing square is 100 square feet of roof surface, and the surface is bigger than the footprint because the roof slopes. The three things you need from the roof are the footprint, the pitch, and the edges — eaves, rakes, ridges, hips and valleys — because the materials that run along an edge are ordered by the foot, not by the square.
The example roof
- Footprint 40 × 30 ft = 1,200 sq ft of plan.
- At 6/12 the slope factor is 1.118, so the surface is 1,341.6 sq ft — 13.42 squares.
- Edges on a gable: 80 ft of eave, 67.1 ft of rake, 40 ft of ridge.
From the ground, the squares calculator does this from a length, a width and a pitch. On a real roof, trace the outline on the aerial photo and the squares and every edge length come back measured — your own measurement, which is right for ordering and bidding and is not the report an adjuster signs off.
2. Materials from the takeoff
The takeoff turns squares and edge lengths into things a supplier sells: bundles of shingles, rolls of underlayment, bundles of starter and cap, pieces of drip edge, cartons of nails. Waste goes on the shingles before they are divided into bundles — 10% on this roof, so 14.76 squares are bought to cover 13.42— and every quantity is rounded up to a whole sale unit, because nobody sells a third of a bundle.
| Material | Quantity | Each | Cost |
|---|---|---|---|
| Architectural (laminated) | 45 bundles | $36.50 | $1,642.50 |
| Synthetic underlayment (10 sq roll) | 2 rolls | $110.00 | $220.00 |
| Plastic cap nails — 1 in plastic cap nails, 2,000 per box | 1 box | $45.00 | $45.00 |
| Starter strip — Owens Corning Starter Strip Plus, split (105 ft) | 2 bundles | $55.00 | $110.00 |
| Hip and ridge cap — GAF Seal-A-Ridge (25 ft) | 2 bundles | $48.00 | $96.00 |
| Drip edge (10 ft pieces) | 16 pieces | $12.00 | $192.00 |
| Roofing nails — Coil carton (7,200 nails, approx. 31 lb) | 1 carton | $120.00 | $120.00 |
| Materials | $2,425.50 | ||
The coverage behind each line — bundles per square, square feet per roll, lineal feet per bundle of starter and cap — is the manufacturer’s published figure, and the data sheet each came from is listed on how the math works. Price the list from your supplier, not from a guide.
3. Labor by the square
Most crews price installation per square, and tear-off per square per layer, because that is how the work scales. The other way is production: squares an hour, a crew size and an hourly rate, with fixed hours for setup and cleanup; the bid calculator offers both and they should land close on a roof you know.
- Tear-off, 1 layer: 13.42 sq × $55.00 = $737.90
- Install labor: 13.42 sq × $155.00 = $2,079.54
- Dumpster and disposal: $450.00
- Permit: $250.00
- Direct cost, everything above added up: $5,942.94
The dumpster and the permit are real costs of this job and belong in the direct cost with the labor. What does not belong here yet is anything you have not seen: decking you will not know about until the roof is open, steep-pitch and height charges, detach-and-reset for a dish or a solar array. Those go on the proposal as exclusions or allowances, in step 6, not silently into the price.
4. Overhead
Overhead is what the business costs to run whether or not this job happens — trucks, insurance, the phone, the office — and it is applied to the direct cost before profit, not rolled into it. Rolling the two into one number is how a contractor ends up busy and broke. It is your figure: last year’s fixed costs divided by last year’s revenue is the usual way to arrive at it, and the example uses 10%.
10% of $5,942.94 is $594.29, so the total cost is $6,537.23. That is what the job costs to do. Everything from here on is what you earn on it.
5. Markup against margin, and what a roofing profit margin is
Markup and margin are definitions, not measurements, and confusing them is the single most expensive mistake in contracting. Markup is measured against cost; margin is measured against price. They coincide only at zero.
The same 35%, both ways
- At a 35% margin: $6,537.23 ÷ (1 − 0.35) = $10,057.28, or $749.63 a square. That is a 53.8% markup.
- At a 35% markup: $6,537.23 × (1 + 0.35) = $8,825.26, which earns a 25.9% margin, not 35%.
- The difference on this one roof: $1,232.02 of profit, given away by typing the right number into the wrong box.
So what should a roofing profit margin be? Yours, and we will not hand you a figure. The 35% in the example is there to show the arithmetic, not as a recommendation, and a number pulled from a guide knows nothing about your overhead, your market or your winter. What the arithmetic does settle is which number to think in: margin, because it is the share of the money coming in that you keep, and it is the one that compares to anything else you read about a business. Markup is easier to apply in your head at the van. Whichever you pick, know which one you picked — the bid calculator asks, and then shows you both.
6. What goes on the proposal
The homeowner is comparing your page against somebody else’s, so it has to say what the money buys in words they can check. The itemized lines are the marked-up cost lines spread in proportion, and they add up to the price exactly — $10,057.28 on this roof, to the cent — because an estimate whose lines do not sum to the total under them is one the customer stops trusting.
- The scope in plain words. Tear off how many layers, the underlayment and the shingle line by name, starter, cap, drip edge, the flashing you will replace, and cleanup with a magnet sweep.
- The price, and whether it is itemized or one line. Most homeowners are given a single line for the complete replacement; an itemized page is for the ones who ask, and for an adjuster.
- Exclusions and allowances. Decking replacement priced per sheet, steep or height charges, detach-and-reset, and anything else you could not see from the ground. Written down now, they are a change order later; left off, they are an argument.
- Sales tax, if your state charges it on this work. Many states tax materials and not labor on a re-roof; some tax the whole contract. It is a genuine choice and nobody can make it for you from a guide.
- The terms. The deposit and when the balance is due, a start window, the warranty on the labor and the manufacturer’s on the shingle, your license number and insurance, and a line for both signatures.
The proposal template has every one of those in the right order, and the estimate PDF prints the itemized version with the lines summing to the total.
7. The deposit
A deposit covers the material order and commits the homeowner before the shingles are on the truck. It is a rate of the total, stated on the proposal, and the balance is due on completion.
At 30% of $10,057.28, the deposit on the example is $3,017.18 and the balance due on completion is $7,040.10.
Some states cap the deposit a home-improvement contractor may take, as a share of the contract or as a dollar amount. Check your own rule before you print a percentage, and put your payment link on the proposal so the deposit arrives the same day the homeowner says yes.
Run your own roof through it
Trace the roof on the aerial photo, put in your supplier’s prices and your rate, and the bid comes back priced good/better/best and ready to send. Free for 3 live jobs, no card.